Just How To Install A Bath Tub (For Novices).
Just How To Install A Bath Tub (For Novices).
Blog Article
On this page down the page you can locate a bunch of brilliant ideas around How to Install a Bathtub Yourself.
Mounting a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently available, the task can relocate rapidly; if you need to open a wall to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and also set in the new one. Ensure you have qualified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to take into consideration using one before you begin. Chances are you may need a professional plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have actually already bought a new bathtub and also do not require to change the arrangement of your previous supply of water pipes.
Your devices as well as product list need to consist of the following:
Preparing for the Installation
To start with, the sustaining structure provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to stop stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you should do is separate the supply of water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will come from the pipes. Once the supply pipelines have been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before going on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost flexible tap port to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the supply of water and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally examine the overflow outlet and the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait till the bath tub has been utilized a minimum of when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in area in between the tap and the sink. Secure the faucet in position with the manufacturer provided backnut. Once the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, causing issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the bath tub with water prior to securing, to allow for the activity experienced when the tub is in use. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily readily available on the market. It is a good idea to fit the tiles making use of water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that blog posting on Tools You Need to Install a New Bathtub while scouting around the web. Those who appreciated our article kindly remember to share it. We enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.
Pricing Report this page